When many groups run one experiment, small temperature differences between benches can change results. A Constant Temperature Water Bath holds samples at a set temperature so those differences shrink. This guide explains how it works, where it helps, and what to review before choosing one.
How a Constant Temperature Water Bath Holds Temperature
A constant temperature water bath in laboratory settings keeps a tank of water at a set value so vessels sit in uniform heat. Water transfers heat more evenly than air, which is why a laboratory water bath is a familiar tool for incubation, warming, and controlled reactions.
The Constant Temperature Water Bath LZ-CWB-A105 pairs PID control with a PT100 sensor. The sensor reads the water temperature, and PID control adjusts heating so the reading stays close to the setpoint. The page lists a non-heat centrifugal circulation pump for uniform temperature distribution, plus built-in safeguards against dry heating, temperature deviations, and power interruptions.
Two terms are easy to confuse. Fluctuation is variation over time at one point, while uniformity is variation across the bath. The page lists ±0.005 to ±0.01 °C for both.
Constant Temperature Water Bath Diagram: Main Parts
A simple constant temperature water bath diagram for this model shows how a few parts work together
- Inner chamber: 5 L, with an inner groove of 275×190×120 mm
- Work slot: 180×140 mm
- PT100 sensor: reads the water temperature for PID control
- Circulation pump: moves water to even out the temperature
- LCD: shows the set value and the live reading
- Drain: empties the tank after use
Constant Temperature Water Bath Uses in Teaching and Research
Constant temperature water bath uses reach well beyond a single class. According to the product page, the LZ-CWB-A105 supports the following work:
- Laboratory research, including chemical, biological, and pharmaceutical experiments
- Sample incubation and routine workflows
- Material testing for metals, polymers, and other samples
- Industrial testing and sample preparation
- Environmental testing labs
In a university, the same bath can serve a teaching session in the morning and a research group later in the day. Among the constant temperature water bath benefits for teaching, groups heat samples to the same temperature, so differences in results come from the experiment rather than the equipment. The LCD also lets instructors and learners watch the setpoint and live reading together, which builds good lab habits.
Published Details of the LZ-CWB-A105
| Parameter | Details |
|---|---|
| Capacity | 5 L |
| Temperature range | Room temperature to 100 °C |
| Temperature fluctuation | ±0.005 to ±0.01 °C |
| Temperature uniformity | ±0.005 to ±0.01 °C (horizontal and vertical) |
| Sensor and control | PT100 sensor, PID control |
| Display | LCD |
| Interface | RS232 or RS485 |
| Work slot | 180×140 mm |
| Inner groove | 275×190×120 mm |
| Drain | Yes |
Basic Bath Versus Temperature Controlled Water Bath
A temperature water bath can range from a simple heated tank to a controlled system with sensors and circulation. A temperature controlled water bath is the better fit when results depend on a narrow temperature window.
| Feature | Basic heated tank | Controlled constant temperature bath |
|---|---|---|
| Temperature control | Simple thermostat | Sensor with digital control |
| Water movement | Often still | Circulation for even temperature |
| Readout | Dial or none | Digital display |
| Data connection | Rare | Optional interface on some models |
A constant temperature bath for laboratory use is judged by stability, circulation, and display, not by heating alone.
Constant Temperature Water Bath Laboratory Use: Step-by-Step
- Place the bath on a level, stable bench near a suitable outlet.
- Fill the tank with clean water to the level shown in the manual.
- Set the target temperature on the LCD and let the water reach it.
- Wait for the live reading to settle.
- Place sealed samples or vessels inside, within the work slot.
- Monitor the temperature for the time your method requires.
- Remove samples carefully, switch off, and let the water cool.
- Use the drain to empty the tank, then wipe it dry.
Read the user manual before the first run.
Common Selection Mistakes
The most frequent mistake is treating any heated tank as equal. Review capacity, temperature range, stability figures, circulation, and display together. A 5 L chamber suits small groups and compact benches, while larger class sets may need more capacity or more than one bath.
Another mistake is ignoring bench space and electrical details, since the page does not list weight or voltage. Confirm both before ordering. To weigh other formats, browse the bath and circulator range before narrowing your shortlist.
User Tips and Recommended Practices
- Use clean water, because mineral buildup affects the tank over time.
- Never run the bath dry; fill before heating, even though safeguards exist.
- Let the temperature settle before adding samples.
- Use containers suited to the temperature you set.
- Label positions so each group or sample is tracked.
- Teach safe lifting and splash habits around hot water.
- Log setpoint, time, and sample details for each run.
- Drain and wipe the tank after use to prevent residue.
- Review the manufacturer’s instructions before the first run.
Exploring the Bath and Circulator Category
The Constant Temperature Water Bath LZ-CWB-A105 belongs to the wider group of laboratory baths and circulators, which includes water baths, heating circulators, and cooling circulators. Buyers usually compare capacity, temperature range, stability, circulation, display type, and available accessories. To see the full range, visit the bath and circulator category.
Labozon supplies scientific equipment across many disciplines, and the rest of its catalog is reachable from the Labozon home page.
Looking for constant temperature water bath?
Compare available models, review product specifications, and contact the Labozon team for assistance in identifying equipment that matches your laboratory requirements.